Infors HT Ecotron Скачать руководство пользователя страница 66

Страница: 66 / 93

Ecotron - Incubation Shaker

Rectifying Faults

Page

03 May 2018

Alarm message

Meaning

The rotation speed is too high.

Possible cause

Measures

Personnel

Error when measuring the ro-

tation speed.

Switch the equipment off and then on again.

Operator

The drive control system is

defective.

Contact your local Infors representative and re-

place the control rack (see chapter 10.2, page

73).

Operator

The motor is defective.

Contact your local Infors representative.

Infors service techni-

cian or licensed dealer

Alarm message

Meaning

The equipment door is open.

8.2 Fault Tables

The tables below describe potential faults that do not usually trig-

ger an error message on the display or – with a few exceptions –

an alarm signal. In many cases, operators can resolve these faults

themselves.

General faults

Fault

After activating the main switch, the view boxes do not light up.

Possible cause

Measures

Personnel

Power supply to equipment in-

terrupted.



Check if the plugs are plugged in correctly.



Check the mains connection.

Operator

The equipment fuse is defec-

tive.

Replace equipment fuse (see chapter 10.1, page

72).

Operator

Fault

The interior lighting does not work.

Possible cause

Measures

Personnel

The lighting element of the in-

terior lighting is defective.

Replace the lighting element (see chapter 10.3,

page 74).

Operator

Содержание Ecotron






























































































Результаты поиска

Содержание Ecotron

Отзывы:

Похожие инструкции для Ecotron

Бренды по названию

Популярные бренды

Infors HT Ecotron, Руководство по эксплуатации

Результаты поиска

Содержание Ecotron

Отзывы:

Похожие инструкции для Ecotron

Бренды по названию

Популярные бренды