Infors HT Ecotron Скачать руководство пользователя страница 67

Страница: 67 / 93

Ecotron - Incubation Shaker

Rectifying Faults

03 May 2018

Page

Faults related to the “Rotation speed” parameter

Fault

The table does not move.

Possible cause

Measures

Personnel

The “Rotation speed” parame-

ter is not activated.

Activate the parameter.

Operator

The table is blocked by for-

eign objects.

Dismantle table and remove foreign objects.

Operator

The load is too heavy, making

the drive too weak or causing

it to overheat.

Reduce the load.

If the drive has overheated, the process can be

continued after it has cooled down.

Operator

The drive has heated up too

much, and has been turned

off automatically.

Let the equipment cool down. Ensure that the air

vents on the side are unobstructed.

Operator

The cable from the shaker to

the control rack has been un-

plugged.

Plug in the cable.

Operator

The drive control system is

defective.

Contact your local Infors representative and re-

place the control rack (see chapter 10.2, page

73).

Operator

The drive belt is torn.

Contact your local Infors representative and have

the drive belt replaced.

Infors service techni-

cian or licensed dealer

The motor is defective.

Contact your local Infors representative.

Infors service techni-

cian or licensed dealer

Fault

Strong vibrations occur.

Possible cause

Measures

Personnel

The load is too heavy, so the

equipment is not balanced.

Reduce the load to the prescribed value.

Operator

The load is too light, so the

equipment is not balanced.

Increase the load to the prescribed value.

Operator

The load is distributed une-

venly.

Load the tray in the centre. If possible, do not

place any heavy weights in the corners of the

tray.

Operator

The rotation speed is too high. Reduce the rotation speed.

Operator

The equipment is not standing

straight.

Place the equipment on an flat surface.

Operator

The substructure (table) is too

weak.

Place the equipment on a stable table or the

floor.

Operator

The liners of the table are

worn.

Contact your local Infors representative and re-

place the liners (see chapter 10.5, page 76).

Operator

Содержание Ecotron






























































































Результаты поиска

Содержание Ecotron

Отзывы:

Похожие инструкции для Ecotron

Бренды по названию

Популярные бренды

Infors HT Ecotron, Руководство по эксплуатации

Результаты поиска

Содержание Ecotron

Отзывы:

Похожие инструкции для Ecotron

Бренды по названию

Популярные бренды