Infors HT Ecotron Скачать руководство пользователя страница 53

Страница: 53 / 93

Ecotron - Incubation Shaker

Operation

03 May 2018

Page

7.2.3 Fitting the Tray

The table features threaded holes which make it possible to mount

holders and clamps directly on the table. Alternatively, trays with

fixtures can be ordered from the manufacturer and fitted onto the

table. To do so, proceed as follows:

Procedure

Place the tray on the table so that no edge sticks out.

Fix the tray to the table using the supplied Phillips-head

screws. Evenly tighten the Phillips-head screws cross-wise.

ATTENTION

If the tray is not affixed securely to the table, the tray may dam-

age the interior of the table when moving.
– Do not start up the equipment unless the tray has been in-

serted correctly and affixed.

Screw sizes

Tray with pin holders: Philips-head M4x8
Tray with sliding bars: Philips-head M4x8
Tray with «Sticky Stuff» adhesive matting: Philips-head M4x6

7.2.4 Fitting the Intermediate Base

An intermediate base for static incubation is available as an acces-

sory. The maximum load of the intermediate base is 5 kg for point

loads. To prevent longer lasting cultures from drying out, we rec-

ommend placing suitable sealing tape (e.g. parafilm) on the agar

plates or placing the plates in an open plastic bag.

Содержание Ecotron






























































































Результаты поиска

Содержание Ecotron

Отзывы:

Похожие инструкции для Ecotron

Бренды по названию

Популярные бренды

Infors HT Ecotron, Руководство по эксплуатации

Результаты поиска

Содержание Ecotron

Отзывы:

Похожие инструкции для Ecotron

Бренды по названию

Популярные бренды