Infors HT Ecotron Скачать руководство пользователя страница 51

Страница: 51 / 93

Ecotron - Incubation Shaker

Operation

03 May 2018

Page

7.2.2 Fitting the Holders

ATTENTION

The threaded holes of the table can be damaged if the fastening

screws are not screwed straight into the thread:
– Place the screws vertically on the drill holes.
– Ensure they can be tightened easily.

ATTENTION

All holders are supplied with pre-fitted screws. If a test tube

holder or a box for microtiter plates is placed on the «Sticky

Stuff» adhesive matting, there is a risk that the adhesive matting

is damaged by protruding screws.
– Remove the screws before you place test tube holders or

boxes for microtiter plates on the «Sticky Stuff» adhesive

matting.

Fitting a holder

Clamps, test tubes and boxes for microtiter plates are fixed to the

table using screws. The equipment is delivered with pre-fitted

screws (2). The screws are each secured with one flat gasket at

the bottom (1) so that they cannot fall out. Only use the screws

provided or screws of the same size for assembly.

To fit a holder, proceed as follows:

Procedure

Loosen flat gaskets.

Position the holder on the table.

Centre a screw on the threaded hole in the table and screw it

in loosely. It must still be possible to turn the holder.

Align the holder so that all screws are vertical above the re-

spective threaded hole in the table.

Insert screws loosely. Ensure that the screws are screwed in

straight and do not tilt.

Evenly tighten all screws cross-wise.

Содержание Ecotron






























































































Результаты поиска

Содержание Ecotron

Отзывы:

Похожие инструкции для Ecotron

Бренды по названию

Популярные бренды

Infors HT Ecotron, Руководство по эксплуатации

Результаты поиска

Содержание Ecotron

Отзывы:

Похожие инструкции для Ecotron

Бренды по названию

Популярные бренды