Husqvarna 701 Enduro 2017 Скачать руководство пользователя страница 133

Страница: 133 / 216

14 WHEELS, TIRES

131

Warning

Danger of accidents

Non-approved or non-recommended tires and wheels impact the handling characteristic.

–

Only use tires/wheels approved by Husqvarna Motorcycles with the corresponding speed index.

Warning

Danger of accidents

Reduced road grip with new tires.

–

New tires have a smooth rolling surface and therefore cannot provide full road grip. The entire rolling surface must be rough-

ened in the first 200 kilometers (124.3 miles) by moderate riding at alternating angles. The full grip levels are not achieved

until the tires have been run in.

Info

The type, condition, and air pressure of the tires all have a major impact on the handling characteristics of the motorcycle.
Worn tires have a negative effect on handling characteristics, especially on wet surfaces.

400602-10

–

Check the front and rear tires for cuts, run-in objects, and other damage.
» If the tires have cuts, run-in objects, or other damage:

–

Change the tires.

–

Check the tread depth.

Info

Adhere to the legally required minimum tread depth.

Minimum tread depth

≥

2 mm (

≥

0.08 in)

» If the tread depth is less than the minimum tread depth:

–

Change the tires.

Содержание 701 Enduro 2017

























































































































































































































Результаты поиска

Содержание 701 Enduro 2017

Отзывы:

Похожие инструкции для 701 Enduro 2017

Бренды по названию

Популярные бренды

Husqvarna 701 Enduro 2017, Руководство пользователя

Результаты поиска

Содержание 701 Enduro 2017

Отзывы:

Похожие инструкции для 701 Enduro 2017

Бренды по названию

Популярные бренды