Husqvarna 701 Enduro 2017 Скачать руководство пользователя страница 94

Страница: 94 / 216

12 SERVICE WORK ON THE CHASSIS

V00509-10

Main work

–

Loosen nut



–

Remove nuts



on the left and right.

–

Adjust the chain tension by turning adjusting screws



left and right.

Guideline

Chain tension

5 mm (0.2 in)

Turn the adjusting screws



on the left and right so that the markings on the left

and right chain adjusters



are in the same position relative to the reference

marks



. The rear wheel is then correctly aligned.

Info

The upper part of the chain must be taut.
Chain wear is not always even. Repeat this measurement at different chain

positions.

–

Tighten nuts



–

Make sure that chain adjusters



are fitted correctly on adjusting screws



–

Tighten nut



Guideline

Nut, rear wheel spindle

M25x1.5

90 Nm (66.4 lbf ft)

Finishing work

–

Remove the motorcycle from the lift stand. (

p. 77)

Содержание 701 Enduro 2017

























































































































































































































Результаты поиска

Содержание 701 Enduro 2017

Отзывы:

Похожие инструкции для 701 Enduro 2017

Бренды по названию

Популярные бренды

Husqvarna 701 Enduro 2017, Руководство пользователя

Результаты поиска

Содержание 701 Enduro 2017

Отзывы:

Похожие инструкции для 701 Enduro 2017

Бренды по названию

Популярные бренды