Husqvarna 701 Enduro 2017 Скачать руководство пользователя страница 206

Страница: 206 / 216

25 STANDARDS

204

JASO T903 MA

Different technical development directions required a separate specification for 4-stroke motorcycles

–

the

JASO T903 MA

standard.

Earlier, engine oils from the automobile industry were used for 4-stroke motorcycles because there was no separate motorcycle specifi-

cation.
Whereas long service intervals are demanded for automobile engines, the focus for motorcycle engines is on high performance at high

engine speeds.
In most motorcycle engines, the transmission and the clutch are lubricated with the same oil.
The

JASO MA

standard meets these special requirements.

SAE

The SAE viscosity classes were defined by the Society of Automotive Engineers and are used for classifying oils according to their vis-

cosity. The viscosity describes only one property of oil and says nothing about quality.

Содержание 701 Enduro 2017

























































































































































































































Результаты поиска

Содержание 701 Enduro 2017

Отзывы:

Похожие инструкции для 701 Enduro 2017

Бренды по названию

Популярные бренды

Husqvarna 701 Enduro 2017, Руководство пользователя

Результаты поиска

Содержание 701 Enduro 2017

Отзывы:

Похожие инструкции для 701 Enduro 2017

Бренды по названию

Популярные бренды