Husqvarna 701 Enduro 2017 Скачать руководство пользователя страница 35

Страница: 35 / 216

CONTROLS

6.18

Side stand

401943-10

The side stand



is located on the left side of the vehicle.

The side stand is used for parking the motorcycle.

Info

The side stand must be folded up during motorcycle use.
The side stand is coupled with the safety starting system

–

see the riding instruc-

tions.

Possible states

• Side stand folded out

–

The vehicle can be supported on the side stand. The safety

starting system is active.

• Side stand folded in

–

This position is mandatory when riding the motorcycle. The

safety starting system is inactive.

Содержание 701 Enduro 2017

























































































































































































































Результаты поиска

Содержание 701 Enduro 2017

Отзывы:

Похожие инструкции для 701 Enduro 2017

Бренды по названию

Популярные бренды

Husqvarna 701 Enduro 2017, Руководство пользователя

Результаты поиска

Содержание 701 Enduro 2017

Отзывы:

Похожие инструкции для 701 Enduro 2017

Бренды по названию

Популярные бренды