Husqvarna 701 Enduro 2017 Скачать руководство пользователя страница 120

Страница: 120 / 216

13 BRAKE SYSTEM

118

V00517-10

Main work

–

Stand the vehicle upright.

–

Remove screw cap



with membrane



–

Add brake fluid up to the

MAX

marking.

Brake fluid DOT 4 (

p. 200)

–

Mount screw cap with membrane.

Info

Clean up overflowed or spilled brake fluid immediately with water.

13.12

Checking the rear brake linings

Warning

Danger of accidents

Worn-out brake linings reduce the braking effect.

–

Ensure that worn-out brake linings are replaced immediately. (Your authorized Husqvarna Motorcycles workshop will be glad

to help.)

Warning

Danger of accidents

Damaged brake discs reduce the braking effect.

If the brake linings are not changed in time, the brake lining carriers grind against the brake disc. As a consequence, the brak-

ing effect is greatly reduced and the brake discs are destroyed.

–

Check the brake linings regularly.

Содержание 701 Enduro 2017

























































































































































































































Результаты поиска

Содержание 701 Enduro 2017

Отзывы:

Похожие инструкции для 701 Enduro 2017

Бренды по названию

Популярные бренды

Husqvarna 701 Enduro 2017, Руководство пользователя

Результаты поиска

Содержание 701 Enduro 2017

Отзывы:

Похожие инструкции для 701 Enduro 2017

Бренды по названию

Популярные бренды