Husqvarna 701 Enduro 2017 Скачать руководство пользователя страница 123

Страница: 123 / 216

13 BRAKE SYSTEM

121

V00517-10

–

Stand the vehicle upright.

–

Remove screw cap



with membrane



–

Press the brake caliper onto the brake disc by hand in order to push back the brake

piston. Ensure that brake fluid does not flow out of the brake fluid reservoir, extracting

it by suction if it does.

Info

Make sure when pushing back the brake piston that you do not press the

brake caliper against the spokes.

D00955-10

–

Remove cotter pin



, remove pin



toward the left by striking it, and remove the

brake linings.

–

Clean the brake caliper and brake caliper support.

400419-11

–

Check that leaf spring



in the brake caliper and sliding plate



in the brake caliper

support are seated correctly.

–

Insert the new brake linings, insert the pin, and mount the cotter pins.

Info

Always change the brake linings in pairs.

–

Operate the foot brake lever repeatedly until the brake linings are in contact with the

brake disc and there is a pressure point.

Содержание 701 Enduro 2017

























































































































































































































Результаты поиска

Содержание 701 Enduro 2017

Отзывы:

Похожие инструкции для 701 Enduro 2017

Бренды по названию

Популярные бренды

Husqvarna 701 Enduro 2017, Руководство пользователя

Результаты поиска

Содержание 701 Enduro 2017

Отзывы:

Похожие инструкции для 701 Enduro 2017

Бренды по названию

Популярные бренды