Husqvarna 701 Enduro 2017 Скачать руководство пользователя страница 53

Страница: 53 / 216

RIDING INSTRUCTIONS

Warning

Danger of accidents

Reduced road grip with cold tires.

–

On every journey, take the first miles carefully at moderate speed until the tires reach operating temperature and optimal

road grip is ensured.

Warning

Danger of accidents

Reduced road grip with new tires.

–

New tires have a smooth rolling surface and therefore cannot provide full road grip. The entire rolling surface must be rough-

ened in the first 200 kilometers (124.3 miles) by moderate riding at alternating angles. The full grip levels are not achieved

until the tires have been run in.

Warning

Danger of accidents

Unstable handling characteristics.

–

Do not exceed the maximum permitted weight and axle loads. The overall weight consists of: motorcycle operational and

with a full tank, driver and passenger with protective clothing and helmet, baggage.

Warning

Danger of accidents

Unstable handling characteristics due to slipped baggage.

–

Check the way your baggage is fixed regularly.

Warning

Danger of accidents

Lack of roadworthiness.

–

After a fall, check the vehicle as usual before preparing for use.

Note

Engine damage

Unfiltered intake air has a negative effect on the service life of the engine.

Dust and dirt will enter the engine without an air filter.

–

Never start to use the vehicle without an air filter.

Содержание 701 Enduro 2017

























































































































































































































Результаты поиска

Содержание 701 Enduro 2017

Отзывы:

Похожие инструкции для 701 Enduro 2017

Бренды по названию

Популярные бренды

Husqvarna 701 Enduro 2017, Руководство пользователя

Результаты поиска

Содержание 701 Enduro 2017

Отзывы:

Похожие инструкции для 701 Enduro 2017

Бренды по названию

Популярные бренды