Husqvarna 701 Enduro 2017 Скачать руководство пользователя страница 73

Страница: 73 / 216

11 TUNING THE CHASSIS

11.10

Checking the riding sag of the shock absorber

400990-10

–

Measure distance



of rear wheel unloaded. (

p. 69)

–

With another person holding the motorcycle, the rider, wearing full protective cloth-

ing, sits on the seat in a normal sitting position (feet on footrests) and bounces up and

down a few times.

The rear wheel suspension levels out.

–

Another person now measures the distance between the rear axle and the fixed point.

–

Note down the value as dimension



Info

The riding sag is the difference between measurements



and



–

Check the riding sag.

Riding sag

75… 85 mm (2.95… 3.35 in)

» If the riding sag differs from the specified measurement:

–

Adjust the riding sag.

(

p. 74)

Содержание 701 Enduro 2017

























































































































































































































Результаты поиска

Содержание 701 Enduro 2017

Отзывы:

Похожие инструкции для 701 Enduro 2017

Бренды по названию

Популярные бренды

Husqvarna 701 Enduro 2017, Руководство пользователя

Результаты поиска

Содержание 701 Enduro 2017

Отзывы:

Похожие инструкции для 701 Enduro 2017

Бренды по названию

Популярные бренды