Husqvarna 701 Enduro 2017 Скачать руководство пользователя страница 160

Страница: 160 / 216

16 COOLING SYSTEM

158

V00518-10

–

Stand the motorcycle on its side stand on a horizontal surface.

–

Remove cover



of the compensating tank.

–

Check the antifreeze in the coolant.

−

25…

−

45 °C (

−

13…

−

49 °F)

» If the antifreeze in the coolant does not match the specified value:

–

Correct the antifreeze in the coolant.

–

Check the coolant level in the compensating tank.

The coolant level must be between the two markings.

» If the coolant level does not match the specified value:

–

Correct the coolant level.

Coolant (

p. 200)

–

Mount cover



of the compensating tank.

V00520-11

–

Remove radiator cap



–

Check the antifreeze in the coolant.

−

25…

−

45 °C (

−

13…

−

49 °F)

» If the antifreeze in the coolant does not match the specified value:

–

Correct the antifreeze in the coolant.

–

Check the coolant level in the radiator.

The radiator must be filled completely.

» If the coolant level does not match the specified value:

–

Check the coolant level and the reason for the loss.

Coolant (

p. 200)

Содержание 701 Enduro 2017

























































































































































































































Результаты поиска

Содержание 701 Enduro 2017

Отзывы:

Похожие инструкции для 701 Enduro 2017

Бренды по названию

Популярные бренды

Husqvarna 701 Enduro 2017, Руководство пользователя

Результаты поиска

Содержание 701 Enduro 2017

Отзывы:

Похожие инструкции для 701 Enduro 2017

Бренды по названию

Популярные бренды