Husqvarna 701 Enduro 2017 Скачать руководство пользователя страница 135

Страница: 135 / 216

14 WHEELS, TIRES

133

Front

2.0 bar (29 psi)

Rear

2.2 bar (32 psi)

» If the tire pressure does not meet specifications:

–

Correct the tire pressure.

–

Mount the protection cover.

14.8

Checking spoke tension

Warning

Danger of accidents

Incorrectly tensioned spokes impair the handling characteristic and result in secondary damage.

The spokes break due to being overloaded if they are too tightly tensioned. If the tension in the spokes is too low, then lateral

and radial run-out will form in the wheel. Other spokes will become looser as a result.

–

Check spoke tension regularly, and in particular on a new vehicle. (Your authorized Husqvarna Motorcycles workshop will be

glad to help.)

Info

A loose spoke can unbalance the wheel and other spokes may loosen within a short period.
If the spokes are too tight, they can break due to local overload.
Check the spoke tension regularly, especially on a new motorcycle.

Содержание 701 Enduro 2017

























































































































































































































Результаты поиска

Содержание 701 Enduro 2017

Отзывы:

Похожие инструкции для 701 Enduro 2017

Бренды по названию

Популярные бренды

Husqvarna 701 Enduro 2017, Руководство пользователя

Результаты поиска

Содержание 701 Enduro 2017

Отзывы:

Похожие инструкции для 701 Enduro 2017

Бренды по названию

Популярные бренды