Husqvarna 701 Enduro 2017 Скачать руководство пользователя страница 126

Страница: 126 / 216

14 WHEELS, TIRES

124

S01057-10

Warning

Danger of accidents

Damaged brake discs reduce the braking effect.

–

Always lay the wheel down in such a way that the brake disc is not dam-

aged.

–

Holding the front wheel, withdraw the wheel spindle. Take the front wheel out of the

fork.

Info

Do not pull the hand brake lever when the front wheel is removed.

H00934-10

–

Remove spacers



14.2

Installing the front wheel

Warning

Danger of accidents

Oil or grease on the brake discs reduces the braking effect.

–

Always keep the brake discs free of oil and grease.

–

Clean the brake discs with brake cleaner when necessary.

Содержание 701 Enduro 2017

























































































































































































































Результаты поиска

Содержание 701 Enduro 2017

Отзывы:

Похожие инструкции для 701 Enduro 2017

Бренды по названию

Популярные бренды

Husqvarna 701 Enduro 2017, Руководство пользователя

Результаты поиска

Содержание 701 Enduro 2017

Отзывы:

Похожие инструкции для 701 Enduro 2017

Бренды по названию

Популярные бренды