Husqvarna 701 Enduro 2017 Скачать руководство пользователя страница 185

Страница: 185 / 216

21 TROUBLESHOOTING

183

Faults

Possible cause

Action

Engine overheats.

Too little coolant in cooling system

–

Check the cooling system for leakage.

–

Check the coolant level. (

p. 159)

Radiator fins very dirty

–

Clean radiator fins.

Foam formation in cooling system

–

Drain the coolant.

(

p. 161)

–

Fill/bleed the cooling system.

(

p. 162)

Buckled or damaged radiator hose

–

Change the radiator hose.

Thermostat is faulty

–

Check the thermostat.

Fuse

blown

–

Change the fuses of individual power

consumers. (

p. 146)

Defect in radiator fan system

–

Check the radiator fan system.

Air in cooling system

–

Fill/bleed the cooling system.

(

p. 162)

Malfunction indicator lamp lights up or

flashes

Defect in fuel injection system

–

Read out the fault memory using the Husqvarna

Motorcycles diagnostics tool.

The idling speed indicator lamp

does not light up when the transmis-

sion is in neutral

Gear position sensor not programmed

–

Read out the fault memory using the Husqvarna

Motorcycles diagnostics tool.

Engine dies during the journey

Lack of fuel

–

Refuel. (

p. 57)

Fuse

blown

–

Change the fuses of individual power

consumers. (

p. 146)

The ABS warning lamp lights up

The ABS fuse is blown

–

Change the ABS fuses. (

p. 143)

Large difference in wheel speeds of

the front and rear wheels

–

Stop the vehicle, switch off the ignition, and

start it again.

Malfunction in ABS

–

Read out the ABS fault memory using the Husq-

varna Motorcycles diagnostics tool.

Содержание 701 Enduro 2017

























































































































































































































Результаты поиска

Содержание 701 Enduro 2017

Отзывы:

Похожие инструкции для 701 Enduro 2017

Бренды по названию

Популярные бренды

Husqvarna 701 Enduro 2017, Руководство пользователя

Результаты поиска

Содержание 701 Enduro 2017

Отзывы:

Похожие инструкции для 701 Enduro 2017

Бренды по названию

Популярные бренды