Husqvarna 701 Enduro 2017 Скачать руководство пользователя страница 164

Страница: 164 / 216

16 COOLING SYSTEM

162

K00402-10

Main work

–

Position the motorcycle upright.

–

Place a suitable container under the engine.

–

Remove screw



–

Remove the radiator cap.

–

Completely drain the coolant.

–

Mount and tighten screw



with a new seal ring.

Guideline

Plug, drain hole of water pump

M10x1

15 Nm (11.1 lbf ft)

Finishing work

–

Install the engine guard. (

p. 102)

16.5

Filling/bleeding the cooling system

Warning

Danger of poisoning

Coolant is toxic and a health hazard.

–

Keep coolant out of the reach of children.

–

Do not allow coolant to come into contact with the skin, the eyes and clothing.

–

Consult a doctor immediately if coolant is swallowed.

–

Rinse the affected area immediately with plenty of water in the event of contact with the skin.

–

Rinse eyes thoroughly with water and consult a doctor immediately if coolant gets into the eyes.

–

Change clothing if coolant spills onto your clothing.

Содержание 701 Enduro 2017

























































































































































































































Результаты поиска

Содержание 701 Enduro 2017

Отзывы:

Похожие инструкции для 701 Enduro 2017

Бренды по названию

Популярные бренды

Husqvarna 701 Enduro 2017, Руководство пользователя

Результаты поиска

Содержание 701 Enduro 2017

Отзывы:

Похожие инструкции для 701 Enduro 2017

Бренды по названию

Популярные бренды