Husqvarna 701 Enduro 2017 Скачать руководство пользователя страница 79

Страница: 79 / 216

12 SERVICE WORK ON THE CHASSIS

12.1

Raising the motorcycle with a lift stand

Note

Danger of damage

The parked vehicle can roll away or fall over.

–

Park the vehicle on a firm and level surface.

401942-01

–

Use the underride guard underneath the engine to raise the vehicle.

Neither wheel is in contact with the ground.

–

Secure the motorcycle against falling over.

12.2

Removing the motorcycle from the lift stand

Note

Danger of damage

The parked vehicle can roll away or fall over.

–

Park the vehicle on a firm and level surface.

Содержание 701 Enduro 2017

























































































































































































































Результаты поиска

Содержание 701 Enduro 2017

Отзывы:

Похожие инструкции для 701 Enduro 2017

Бренды по названию

Популярные бренды

Husqvarna 701 Enduro 2017, Руководство пользователя

Результаты поиска

Содержание 701 Enduro 2017

Отзывы:

Похожие инструкции для 701 Enduro 2017

Бренды по названию

Популярные бренды