Husqvarna 701 Enduro 2017 Скачать руководство пользователя страница 69

Страница: 69 / 216

11 TUNING THE CHASSIS

Info

The effect of the low-speed setting can be seen in slow to normal compression of the shock absorber.

V00494-10

–

Turn adjusting screw



clockwise with a screwdriver up to the last perceptible click.

Info

Do not loosen fitting



–

Turn counterclockwise by the number of clicks corresponding to the shock absorber

type.
Guideline

Compression damping, low-speed

Standard

15 clicks

Info

Turn clockwise to increase damping; turn counterclockwise to reduce damp-

ing.

11.6

Adjusting the high-speed compression damping of the shock absorber

Caution

Risk of injury

Parts of the shock absorber will fly off if the shock absorber is disassembled incorrectly.

The shock absorber is filled with highly compressed nitrogen.

–

Please follow the description provided. (Your authorized Husqvarna Motorcycles workshop will be glad to help.)

Содержание 701 Enduro 2017

























































































































































































































Результаты поиска

Содержание 701 Enduro 2017

Отзывы:

Похожие инструкции для 701 Enduro 2017

Бренды по названию

Популярные бренды

Husqvarna 701 Enduro 2017, Руководство пользователя

Результаты поиска

Содержание 701 Enduro 2017

Отзывы:

Похожие инструкции для 701 Enduro 2017

Бренды по названию

Популярные бренды