Husqvarna 701 Enduro 2017 Скачать руководство пользователя страница 107

Страница: 107 / 216

13 BRAKE SYSTEM

105

13.2

Adjusting the basic position of the hand brake lever

S01045-10

–

Adjust the basic position of the hand brake lever to your hand size by turning adjust-
ing wheel



Info

Push the hand brake lever forward and turn the adjusting wheel.
Do not make any adjustments while riding.

13.3

Checking the brake discs

Warning

Danger of accidents

Worn-out brake discs reduce the braking effect.

–

Make sure that worn-out brake discs are replaced immediately. (Your authorized Husqvarna Motorcycles workshop will be

glad to help.)

400406-10

–

Check the thickness of the front and rear brake discs at multiple points on each brake

disc to ensure it is at least thickness



Info

Wear will reduce the thickness of the brake disc at the contact surface



the brake linings.

Brake discs - wear limit

Front

4.5 mm (0.177 in)

Содержание 701 Enduro 2017

























































































































































































































Результаты поиска

Содержание 701 Enduro 2017

Отзывы:

Похожие инструкции для 701 Enduro 2017

Бренды по названию

Популярные бренды

Husqvarna 701 Enduro 2017, Руководство пользователя

Результаты поиска

Содержание 701 Enduro 2017

Отзывы:

Похожие инструкции для 701 Enduro 2017

Бренды по названию

Популярные бренды