Husqvarna 701 Enduro 2017 Скачать руководство пользователя страница 108

Страница: 108 / 216

13 BRAKE SYSTEM

106

Rear

4.5 mm (0.177 in)

» If the brake disc thickness is less than the specified value.

–

Change the front brake disc.

–

Change the rear brake disc.

–

Check the front and rear brake discs for damage, cracking, and deformation.
» If the brake disc exhibits damage, cracking, or deformation:

–

Change the front brake disc.

–

Change the rear brake disc.

13.4

Checking brake fluid level of front brake

Warning

Danger of accidents

An insufficient brake fluid level will cause the brake system to fail.

If the brake fluid level drops below the specified marking or the specified value, the brake system is leaking or the brake linings

are worn down.

–

Check the brake system and do not continue riding until the problem is eliminated. (Your authorized Husqvarna Motorcycles

workshop will be glad to help.)

Warning

Danger of accidents

Old brake fluid reduces the braking effect.

–

Make sure that brake fluid for the front and rear brake is changed in accordance with the service schedule. (Your authorized

Husqvarna Motorcycles workshop will be glad to help.)

Содержание 701 Enduro 2017

























































































































































































































Результаты поиска

Содержание 701 Enduro 2017

Отзывы:

Похожие инструкции для 701 Enduro 2017

Бренды по названию

Популярные бренды

Husqvarna 701 Enduro 2017, Руководство пользователя

Результаты поиска

Содержание 701 Enduro 2017

Отзывы:

Похожие инструкции для 701 Enduro 2017

Бренды по названию

Популярные бренды