Husqvarna 701 Enduro 2017 Скачать руководство пользователя страница 163

Страница: 163 / 216

16 COOLING SYSTEM

161

16.4

Draining the coolant

Warning

Danger of scalding

During motorcycle operation, the coolant gets very hot and is under pressure.

–

Do not open the radiator, the radiator hoses or other cooling system components if the engine or the cooling system are at

operating temperature.

–

Allow the cooling system and the engine to cool down before you open the radiator, the radiator hoses or other components

of the cooling system.

–

In the event of scalding, rinse the area affected immediately with lukewarm water.

Warning

Danger of poisoning

Coolant is toxic and a health hazard.

–

Keep coolant out of the reach of children.

–

Do not allow coolant to come into contact with the skin, the eyes and clothing.

–

Consult a doctor immediately if coolant is swallowed.

–

Rinse the affected area immediately with plenty of water in the event of contact with the skin.

–

Rinse eyes thoroughly with water and consult a doctor immediately if coolant gets into the eyes.

–

Change clothing if coolant spills onto your clothing.

Preparatory work

–

Remove the engine guard. (

p. 101)

Содержание 701 Enduro 2017

























































































































































































































Результаты поиска

Содержание 701 Enduro 2017

Отзывы:

Похожие инструкции для 701 Enduro 2017

Бренды по названию

Популярные бренды

Husqvarna 701 Enduro 2017, Руководство пользователя

Результаты поиска

Содержание 701 Enduro 2017

Отзывы:

Похожие инструкции для 701 Enduro 2017

Бренды по названию

Популярные бренды