Husqvarna 701 Enduro 2017 Скачать руководство пользователя страница 58

Страница: 58 / 216

RIDING INSTRUCTIONS

–

Apply the brakes on the motorcycle.

–

Shift gear to neutral.

–

Switch off the ignition by turning the ignition key to the

OFF

position.

Info

If the engine is switched off with the emergency OFF switch and the ignition remains switched on at the ignition lock, power

continues to flow to most power consumers. This discharges the battery. You should therefore always switch off the engine

with the ignition key

–

the emergency OFF switch is intended for emergencies only.

–

Park the motorcycle on a firm surface.

–

Swing the side stand forward with your foot as far as it will go and lean the vehicle on it.

–

Lock the steering by turning the handlebar fully to the left, pressing down the ignition key to the position

and turning it to the posi-

tion . To make the steering lock engage more easily, move the handlebar a little to the left and right. Remove the ignition key.

9.7

Transport

Note

Danger of damage

The parked vehicle can roll away or fall over.

–

Park the vehicle on a firm and level surface.

Note

Fire hazard

Hot vehicle components pose a fire hazard and explosion risk.

–

Do not park the vehicle near to materials which are highly flammable or explosive.

–

Allow the vehicle to cool down before covering it.

Содержание 701 Enduro 2017

























































































































































































































Результаты поиска

Содержание 701 Enduro 2017

Отзывы:

Похожие инструкции для 701 Enduro 2017

Бренды по названию

Популярные бренды

Husqvarna 701 Enduro 2017, Руководство пользователя

Результаты поиска

Содержание 701 Enduro 2017

Отзывы:

Похожие инструкции для 701 Enduro 2017

Бренды по названию

Популярные бренды