Husqvarna 701 Enduro 2017 Скачать руководство пользователя страница 209

Страница: 209 / 216

28 LIST OF SYMBOLS

207

28.1

Red symbols

Red symbols indicate an error condition that requires immediate intervention.

The coolant temperature warning lamp lights up red

–

The coolant temperature has reached a critical value.

The oil pressure warning lamp lights up red

–

Engine oil pressure is too low.

28.2

Yellow and orange symbols

Yellow and orange symbols indicate an error condition that requires prompt intervention. Active driving aids are also represented by

yellow or orange symbols.

ABS warning lamp lights up/flashes yellow

–

ABS is not active. The ABS lamp also lights up if an error is

detected.

The low fuel warning lamp lights up orange

–

The fuel level has reached the reserve mark.

Malfunction indicator lamp lights up/flashes orange

–

The OBD has detected an emission- or safety-critical fault.

28.3

Green and blue symbols

Green and blue symbols reflect information.

The high beam indicator lamp lights up blue

–

The high beam is switched on.

The idle indicator lamp lights up green

–

The transmission is in idle.

Содержание 701 Enduro 2017

























































































































































































































Результаты поиска

Содержание 701 Enduro 2017

Отзывы:

Похожие инструкции для 701 Enduro 2017

Бренды по названию

Популярные бренды

Husqvarna 701 Enduro 2017, Руководство пользователя

Результаты поиска

Содержание 701 Enduro 2017

Отзывы:

Похожие инструкции для 701 Enduro 2017

Бренды по названию

Популярные бренды