HP 316095-B21 - StorageWorks Edge Switch 2/24 Скачать руководство пользователя страница 78

Страница: 78 / 322

2–58

edge switch 2/24 service manual

Diagnostics

Ensure the switch reporting the problem is connected to facility AC power. Inspect the
switch for indications of being powered on, such as:

•

At the front bezel, an illuminated green power LED or amber system error LED.

•

Audio emanations and airflow from cooling fans.

Does the switch appear powered on?

YES

↓

A power distribution problem is indicated. Go to

MAP 0100: Power Distribution

Analysis on page 2-27

. Exit MAP.

At the switch, inspect the amber LED at the top of the CTP. Is the amber LED
illuminated on the switch?

YES

↓

Failure of the CTP is indicated. Go to

MAP 0500: FRU Failure Analysis on

page 2-59

. Exit MAP.

Either a switch-to-PC Internet link problem (Internet too busy or
IP address typed incorrectly) or a switch Ethernet port failure is indicated.

a. Wait approximately five minutes, then attempt to login to the switch again.

b. At the Netsite field (Netscape Navigator) or Address field (Internet Explorer),

type

http://xxx.xxx.xxx.xxx

, where

xxx.xxx.xxx.xxx

is the IP address

of the switch (obtained in

MAP 0000: Start MAP on page 2-6

). The Username

and Password Required dialog box appears.

c. Type the user name and password obtained in

MAP 0000: Start MAP on

page 2-6

, and click OK. If the View panel does not display, wait five minutes and

perform this step again.

Does the EWS interface appear operational with the View panel displayed?

YES

↓

The switch-to-EWS PC connection is restored and appears operational. Exit
MAP.

Failure of the switch Ethernet port is indicated. Go to

MAP 0500: FRU Failure Analysis

on page 2-59

. Exit MAP.

Содержание 316095-B21 - StorageWorks Edge Switch 2/24



































































































































































































































































































































Результаты поиска

Содержание 316095-B21 - StorageWorks Edge Switch 2/24

Отзывы:

Бренды по названию

Популярные бренды

HP 316095-B21 - StorageWorks Edge Switch 2/24, Руководство по обслуживанию

Результаты поиска

Содержание 316095-B21 - StorageWorks Edge Switch 2/24

Отзывы:

Бренды по названию

Популярные бренды