manualshive.com logo in svg

HP 316095-B21 - StorageWorks Edge Switch 2/24, Руководство по обслуживанию

Поделиться
Скачать
HP 316095-B21 - StorageWorks Edge Switch 2/24 Скачать руководство пользователя страница 211

edge switch 2/24 service manual

A–41

Messages

System diagnostics 
cannot run. The 
Operational Status is 
invalid.

System diagnostics 
cannot run on switch 
or Director or Edge 
Switch with failed 
ports.

Replace failed ports.

The add firmware 
process has been 
aborted.

The user aborted the 
process to add a 
firmware version to 
the HAFM server’s 
firmware library.

Verify the firmware addition is 
to be aborted, then click OK 
to continue.

The data collection 
process failed.

An error occurred 
while performing the 
data collection 
procedure.

Try the data collection 
procedure again. If the 
problem persists, contact the 
next level of support.

The data collection 
process has been 
aborted.

The user aborted the 
data collection 
procedure.

Verify the data collection 
procedure is to be aborted, 
then click OK to continue.

The following 
parameters cannot 
be disabled while 
Enterprise Fabric 
Mode is active: 
Insistent Domain ID, 
Rerouting Delay, 
Domain RSCN's.

A user attempted to 
disable one or more 
of these parameters 
at the Configure 
Switch Parameters 
dialog box with the 
switch online and 
Enterprise Fabric 
Mode (SANtegrity 
feature) enabled.

Click Yes to continue and 
disable Enterprise Fabric 
Mode.

The maximum 
number of address 
configurations has 
been reached.

The maximum 
number of address 
configurations that 
can be saved to the 
HAFM server was 
reached.

Delete configurations no 
longer needed to allow one or 
more new address 
configurations to be saved.

The optical 
transceiver is not 
installed.

Information is not 
available for a port 
without an optical 
transceiver installed.

Install an SFP optical 
transceiver in the port.

Message Description

Action

Содержание 316095-B21 - StorageWorks Edge Switch 2/24



































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды