manualshive.com logo in svg

HP 316095-B21 - StorageWorks Edge Switch 2/24, Руководство по обслуживанию

Поделиться
Скачать
HP 316095-B21 - StorageWorks Edge Switch 2/24 Скачать руководство пользователя страница 186

A–16

edge switch 2/24 service manual

Messages

Remote session 
support has been 
disabled.

The connection 
between the 
specified remote 
workstation and the 
HAFM server was 
disallowed.

Consult with the customer’s 
network administrator to 
determine if the workstation 
entry should be modified at 
the Session Options dialog 
box.

Remote sessions are 
not allowed from this 
network address.

Only IP addresses of 
remote workstations 
specified at the 
Session Options 
dialog box are 
allowed to connect to 
the HAFM server.

Consult with the customer’s 
network administrator to 
determine if the IP address is 
to be configured for remote 
sessions.

Resource is 
unavailable.

The specified 
operation cannot be 
performed because 
the product is 
unavailable.

Verify the HAFM 
server-to-product link is up. If 
the link is up, the HAFM 
server may be busy. Try the 
operation again later.

Selection is not a 
World-Wide Name.

The selection made 
is not a world-wide 
name.

Select a valid world-wide 
name before performing this 
operation.

Server shutting 
down.

The HAFM 
application is closing 
and terminating 
communication with 
the attached product.

Reboot the HAFM server. If 
the problem persists, contact 
the next level of support.

SNMP trap address 
not defined.

If an SNMP 
community name is 
defined, a 
corresponding SNMP 
trap recipient address 
must also be defined.

Enter a corresponding SNMP 
trap recipient address.

The Administrator 
user cannot be 
deleted.

The administrator 
user is permanent 
and cannot be 
deleted from the 
Configure Users 
dialog box.

Informational message 
only-no action is required.

Message Description

Action

Содержание 316095-B21 - StorageWorks Edge Switch 2/24



































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды