HP 316095-B21 - StorageWorks Edge Switch 2/24 Скачать руководство пользователя страница 107

Страница: 107 / 322

edge switch 2/24 service manual

2–87

Diagnostics

6. To activate the zone set, click Configure and select Active Zone Set. The

Active Zone Set dialog box displays. Select the zone to be activated and click
Next.

7. The new display summarizes the zone member changes that will be made by

activating the new zone set. Click Next if this reflects the desired zone
change.

8. The new display summarizes switches that will be affected by activating the

new zone set. Click Next if this reflects the desired zone change.

9. The new display directs the user to press Start to activate the zone set. Click

Start to activate the zone set.

Did the zone name change solve the problem and did both switches join through the
ISL to form a fabric?

YES

↓

The switch, associated ISL, and fabric appear operational. Exit MAP.

Contact the next level of support. Exit MAP.

A switch E_Port segmented because a build fabric protocol error was detected.

a. Disconnect the fiber-optic jumper cable from the segmented E_Port.

b. Reconnect the cable to the same port.

Did disconnecting and reconnecting the cable solve the problem and did both switches
join through the ISL to form a fabric?

YES

↓

The switch, associated ISL, and multiswitch fabric appear operational. Exit
MAP.

Initial program load (IPL) the switch (

IML, IPL or Reset the Switch on page 3–29

Did the IPL solve the problem and did both switches join through the ISL to form a
fabric?

YES

↓

The switch, associated ISL, and multiswitch fabric appear operational. Exit
MAP.

Perform the data collection procedure and contact the next level of support. Exit MAP.

Содержание 316095-B21 - StorageWorks Edge Switch 2/24



































































































































































































































































































































Результаты поиска

Содержание 316095-B21 - StorageWorks Edge Switch 2/24

Отзывы:

Бренды по названию

Популярные бренды

HP 316095-B21 - StorageWorks Edge Switch 2/24, Руководство по обслуживанию

Результаты поиска

Содержание 316095-B21 - StorageWorks Edge Switch 2/24

Отзывы:

Бренды по названию

Популярные бренды