HP 316095-B21 - StorageWorks Edge Switch 2/24 Скачать руководство пользователя страница 56

Страница: 56 / 322

2–36

edge switch 2/24 service manual

Diagnostics

Table 2–5

lists event codes, brief explanations of the codes, and the associated steps

that describe fault isolation procedures.

POST/IPL diagnostics detected a FRU failure as indicated by an event code 400 with
supplementary event data.

a. At the Hardware View, click Logs and select Event Log. The Event Log

displays.

b. Examine the first two bytes (0 and 1) of event data.

c. Byte 0 is a FRU code that indicates the failed component. Byte 1

is the slot number of the failed FRU (00 for a nonredundant FRU, and 00 or 01 for
redundant FRUs.

Table 2–6

lists byte 0 FRU codes and associated steps that describe fault

isolation procedures.

Table 2–5: MAP 200: Event Codes

Event

Code

Explanation

Action

400

Power-up diagnostic failure.

Go to

step 4

411

Firmware fault.

Go to

step 7

Table 2–6: MAP 200: Byte 0 FRU Codes

Byte 0

Failed FRU

Action

CTP.

Go to

step 6

Fan module.

Go to

step 5

Power supply.

Go to

step 6

Содержание 316095-B21 - StorageWorks Edge Switch 2/24



































































































































































































































































































































Результаты поиска

Содержание 316095-B21 - StorageWorks Edge Switch 2/24

Отзывы:

Бренды по названию

Популярные бренды

HP 316095-B21 - StorageWorks Edge Switch 2/24, Руководство по обслуживанию

Результаты поиска

Содержание 316095-B21 - StorageWorks Edge Switch 2/24

Отзывы:

Бренды по названию

Популярные бренды