horiba SF-1U Скачать руководство пользователя

Страница: 44 / 60

E-9

6.1.6. Setting

calibration

temperature

Set to 25

℃

at the factory:

The calibration temperature is set to correct the measured flow rate to the value at the
calibration temperature. For example, set this value to "25

℃

" when calibrating a flow meter

designed for one atmospheric pressure.
Follow the setting procedure below:

①

While pressing the SET key “

△

”, turn on the power switch. Hold down the SET key

“

△

” for five seconds. The equipment will be ready for setting the calibration

temperature.

②

Use the SET keys to enter the calibration temperature. The temperature range is 0
to 35

℃

Pressing the SET keys (“

△

”,”

▽

”) simultaneously sets the temperature to

the initial value of 25.0

℃

③

Turn off the power switch to secure the entry. The equipment stores the settings
even after turning off the power.

※

The calibration temperature can be checked by following two ways.



Turn on the power switch. Then the display will show it after the version
number. (Approx. 3sec. )



Press the SET key “

△

” or”

▽

” when the display is showing the temperature.

This operation is not available at Automatic measurement mode.

6.1.7. Turning on the power switch

The version number and the calibration temperature will be on the display just after turning
on the power switch. Both of them are shown for approx. 3sec.

NOTE



Make sure the calibration temperature setting is correct. If the setting is
incorrect, you cannot obtain correct results.



Warm up the equipment for over 10 minutes after turning on the power. If
the sensors are not stable, you cannot obtain correct results.

Содержание SF-1U





























































Результаты поиска

Содержание SF-1U

Отзывы:

Похожие инструкции для SF-1U

Бренды по названию

Популярные бренды

horiba SF-1U, Инструкция по эксплуатации

Результаты поиска

Содержание SF-1U

Отзывы:

Похожие инструкции для SF-1U

Бренды по названию

Популярные бренды