background image

E-iv

 

Precaution Concerning Handling of Gas 

Improper handling of gas can lead to result in serious accidents. 
Thorough care should be given in handling when toxic gas or inflammable gas is used 
in the system. Also, please observe the general precautions of high pressure gas when 
used in the system. 

 
 

1. Exhaust

 

Always connect an exhaust tube when an inflammable gas is used and exhaust 
through a draft to a safe place. 

 
 

2. Handling of High Pressure Gas

 

            - Quoted from 'Handling of High Pressure Gas' issued by the Tokyo 
                                Metropolis High Pressure Gas Prevention of Disasters Association - 
 
       

2-1  General Precautions

 

       (1) Containers without certification cannot be used. 
       (2) Always charge or re-charge gas at an authorized manufacturer. 
              (3) Gas which are each specified is filled in high pressure gas containers.   
                    Be sure no mistakes are made. 
       (4) Always handle the containers with special care. 
          Caution is required when containers are wet from rain which is easy to slip. 

     

  (5) Always fix and secure the container with a rope to prevent toppling or falling   

         

when moving, storing or for consumption of the container. 

              (6) Do not apply any impact or handle the container in a rough manner. 
       (7) Do not use the containers for purpose other than specified. 
       (8) Always maintain a neat and orderly condition to eliminate hazards. 
 
       

2-2  Precautions Required for Consumption

 

       (1) Maintain the temperature of the container to 40 

 or less. 

              (2) Be careful when handling fire and remove matters which are inflammable 

   or combustible. 
(3) Use the container in an erected position and secure firmly with a rope to 
   prevent overturning. 

              (4) Do not use hoses for piping at high pressure parts. 
                    When using a hose at low pressure parts, be sure to clamp it so that the hose   
          will not disconnect during use.   
              (5) When it is necessary to heat the container, valve or piping, be sure to use   

                    warm water of 40 

  or less or a hot compress. 

              (6) Open or close valves slowly and close the valve and place a cap it when   
          discontinuing use. 
       (7) Separate charged containers from containers which are spent. 

 
 
 
 
 

Содержание SF-1U





























































Отзывы: