Hinowa LightLift 15.70 3S Скачать руководство пользователя страница 56 | Manualshive

Страница: 56 / 137

background image

56

On each ground valveblock oil rate is controlled through the proportional valve
managed by the control module.

Depending on the movement required, proportional valve will open accordingly
regulating the oil rate, at the same time the relevant ON-OFF valves (one each
movement) will open feeding the relevant cylinder or drive gear motor.

Ground valveblocks maximum pressure valve has to be calibrated as indicated
on use and maintenance manual, at 180 bar with engine running at max speed.

When the proportional valve coil is not energized, oil flows back to the tank.
Left side ground valveblock controls the two left side outriggers (n.1 and n.2),

the left track drive gear motor and the tracks widening cylinders.
Right side ground valveblock controls the two right side outriggers (n.3 and

n.4) and the right track drive gear motor.

8.4.1

OUTRIGGERS

Outrigger cylinders are controlled by the cylinder valves block that is screwed

on the cylinder, when machine is setup on outriggers oil is kept under pressure
on the cylinder bottom side, against machine weight, by two piloted one-way

valves installed in series on the cylinder valves block.
Another piloted one-way valve is installed on the stem side.
While cylinder movements are in progress the opposite/s one-way valves is/are

piloted to open letting oil flow back to the valveblock.

BOTTOM

ONE-WAY

VALVES

STEM SIDE ONE-

WAY VALVE

«
...
54
55
56
57
58
...
»

Содержание LightLift 15.70 3S










































































































































Отзывы:

Нет отзывов

Похожие инструкции для LightLift 15.70 3S

Бренд: Olimpia splendid Страницы: 40

Бренд: Balboa Страницы: 23

Бренд: SMT Страницы: 24

Бренд: NewArc Страницы: 12

Бренд: DOLD Страницы: 20

iO-GRID M GFDO-RM01N

Бренд: DAUDIN Страницы: 25

Бренд: A-T Controls Страницы: 19

Бренд: Tarfire Страницы: 31

Бренд: ICP DAS USA Страницы: 7

Torchmate Flexcut 80

Бренд: Lincoln Electric Страницы: 2

Бренд: ESAB Страницы: 239

Бренд: ubbink Страницы: 12

Бренд: Pro Spot Страницы: 44

Invertig 221 AC/DC

Бренд: HTP Страницы: 28

Бренд: Siemens Страницы: 49

Бренд: Siemens Страницы: 105

Бренд: Siemens Страницы: 142

Бренд: Siemens Страницы: 172

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды