Hinowa LightLift 15.70 3S Скачать руководство пользователя страница 66

Страница: 66 / 137

Electronic boards and electrical system components are designed and
manufactured according to the specific standard for automotive components

and are equipped with self-protection systems.

The machine electronic boards communicating in CAN BUS are the followings



MASTER BOARD (ECM1)



LOAD CELL BOARD (ECM3)



REMOTE CONTROL BOARD



MODEM BOARD

For lithium version, also the main lithium components communicate through
CAN BUS:



BMS



BATTERY CHARGER



INVERTER

Further details about lithium are detailed in Lithium technical training.

The ECM1 has 5 different lines (10 wires) for CAB BUS communication:



CAN BUS 0 = Diagnostic plug, modem



CAN BUS 1 = Cylinder position sensors, ECM3, remote control



CAN BUS 2 = Free (ECM4 for bigger machines models)



CAN BUS 3 = Inclination Sensor



CAN BUS 4 = (Lithium system)

9.4

SENSORS COMMUNICATING THROUGH CAN-BUS

Together with those boards some machine sensors interact through CAN BUS

system.

boom cylinder is equipped with an internal sensor that detect the

opening position of the cylinder, it communicates through CAN BUS.

Inclination sensor communicates

through CAN BUS and it’s installed on

the rear side of the machine frame.

CYLINDER

POSITION

SENSOR

Содержание LightLift 15.70 3S










































































































































Результаты поиска

Содержание LightLift 15.70 3S

Отзывы:

Похожие инструкции для LightLift 15.70 3S

Бренды по названию

Популярные бренды

Hinowa LightLift 15.70 3S, Техническое руководство

Результаты поиска

Содержание LightLift 15.70 3S

Отзывы:

Похожие инструкции для LightLift 15.70 3S

Бренды по названию

Популярные бренды