Hinowa LightLift 15.70 3S Скачать руководство пользователя страница 24

Страница: 24 / 137

When machine is not closed and
aligned, if operator try to move an

outrigger display will remind that
machine need to be closed and aligned

by the error message aside.

NOTE: If during the stabilization the photocells lose the signal, for example due
to movements in progress,

the “MACHINE CLOSED AND ALIGNED”

icon

disappears but the movements will continue for a while

even if signal doesn’t

come back.

4.2.1 AUTOMATIC STABILIZATION

To be able to automatically stabilize the machine it must be closed and aligned,
to automatically stabilize the machine it has to be press remote control button

n.7 “AUTO

STABILIZATION” and

keep it pressed until that

display shows “OK”.

AUTO-STABILIZATION procedure sets all the outriggers at the ground and

automatically levels the machine on both axles “X” and “Y”, w

hile the procedure

is in progress the display shows

“WAIT” and the outriggers conditions, as

indicated by the following example.

ERROR

“MACHINE

CLOSED AND

ALIGNED”

ICON

“

AUTO-STABILIZATION

”

BUTTON

PHOTOCELLS

REFLECTOR

Содержание LightLift 15.70 3S










































































































































Результаты поиска

Содержание LightLift 15.70 3S

Отзывы:

Похожие инструкции для LightLift 15.70 3S

Бренды по названию

Популярные бренды

Hinowa LightLift 15.70 3S, Техническое руководство

Результаты поиска

Содержание LightLift 15.70 3S

Отзывы:

Похожие инструкции для LightLift 15.70 3S

Бренды по названию

Популярные бренды