Hinowa LightLift 15.70 3S Скачать руководство пользователя страница 114

Страница: 114 / 137

114

To better find the photocells beam points it’s better to

darken the reflector

and put a strip of tape on it.

In case of need, to verify their calibration put one strip of tape on the first boom

flange and another one on the slew ring as indicated above, signing the
alignment position with two correspondent rows.
After having removed the tape from the reflector, rotate the turret on right side

until the alignment icon will disappear, signing right excursion, then do the

same on left side verifying that excursions “L” and “L1” are the same.

APPENDIX 6

–

MASTER BOARD (ECM1) REPLACEMENT AND SETTING

Machine software contains the software for all the TTC Hinowa machine
models produced till that moment, so that when a new master board (ECM1)

in installed on a machine, the machine model need to be selected.

NEW MASTER BOARD
When a new master board (never used) is fitted on the machine, the remote

control need to be connected to its ground cable and the control position
selected accordingly by the control position selector switch.

Then, turning on the main key, it will require the setting of the machine
model and version, as indicated by the here below procedure.

The set the master board, machine must be closed and aligned, it has to be
make sure that battery is charged enough or machine need to be plugged to

the electric network.

Содержание LightLift 15.70 3S










































































































































Результаты поиска

Содержание LightLift 15.70 3S

Отзывы:

Похожие инструкции для LightLift 15.70 3S

Бренды по названию

Популярные бренды

Hinowa LightLift 15.70 3S, Техническое руководство

Результаты поиска

Содержание LightLift 15.70 3S

Отзывы:

Похожие инструкции для LightLift 15.70 3S

Бренды по названию

Популярные бренды