Hinowa LightLift 15.70 3S Скачать руководство пользователя страница 93

Страница: 93 / 137

10.1.9.8.6

OPTIONAL (PAGE 2)

PAGE 2

The here aside picture shows the OPTIONAL menu second

page display.

Pressing button n.7 it’s possible to come back to the first page

of settings.
Pressing button n.9 (ESC) brings back to the EXTRA menu.

10.1.9.8.6.1

SERVICE

By this page it’s possible to set the service reminder, after
having inserted the relevant password “4538”, pressing

button n.1 “ON” service reminder will be activated, pressing
button n.2 “OFF” it will be deactivated.

The amount of hours considered is the sum of engine and

electric motor ones.

Pressing button n.3 “RESET”

those hours counter is reset,

keeping pressed button n.5 with buttons n.7 and n.8 it is
modified. Instead keeping pressed button n.6 with buttons

n.7 and n.8 is modified the service hours amount.

10.1.9.8.6.2

RC SPEED

By this page it’s possible to set the RC SPEED function, when

it is activated it avoids to operate tracks maximum speed

when operator is not into the basket.

After having inserted the relevant password “4771”, pressing

button

n.1 “ON” second speed will be activated, pressing

button n.2 “OFF” it will be deactivated.

10.1.9.8.6.3

RC MOVE

By this page it’s possible to set the RC MOVE function, when

it is activated it binds the operator standing out from the
basket to press button n.8 to move tracks

After having inserted the relevant password “4771”, pressing

button n.1 “ON” second speed will be activated, pressing
button n.2 “OFF” it will be deactivated.

10.1.9.8.6.4

AD TEST

This menu is used by Hinowa.

10.1.9.8.6.5

AS TEST

This menu is used by Hinowa.

OPTIONAL

1 SERVICE

2 RC SPEE

3 RC MOV

4 AD TEST

5 AS TEST

6 SKYGUARD

7 PREV.

8 NEXT

9 ESC

       SERVICE
HOURS:
       0
SERV:
      50

1 ON

2 OFF

3 RESET

9 ESC

RC SPEED

1 ON

2 OFF *

9 ESC

RC MOVE

1 ON

2 OFF *

9 ESC

Содержание LightLift 15.70 3S










































































































































Результаты поиска

Содержание LightLift 15.70 3S

Отзывы:

Похожие инструкции для LightLift 15.70 3S

Бренды по названию

Популярные бренды

Hinowa LightLift 15.70 3S, Техническое руководство

Результаты поиска

Содержание LightLift 15.70 3S

Отзывы:

Похожие инструкции для LightLift 15.70 3S

Бренды по названию

Популярные бренды