Hinowa LightLift 15.70 3S Скачать руководство пользователя страница 109

Страница: 109 / 137

109

APPENDIX 1

–

TILT SENSOR CALIBRATION

After having replaced the master board (ECM1) or the tilt sensor

it’s necessary

to calibrate its accelerometer system.
Tilt sensor installation need to be done as indicated here below with the screws
5x45 TCEI and Loctite, the distance between the plate and the sensor must be

15 mm.

Being tilt sensor feedback depending on its installation (inclinations on X and Y

axles) it’s necessary to calibrate

it once installed on the machine.

By this procedure the calibration parameters relevant to the accelerometers
will be memorized on the ECM1.

To reset accelerometers, machine need to be settled up on the outriggers, with

aerial part closed and aligned with the photocells.
The accelerometers reset must be done while machine is perfectly levelled in

both axles, both motors need to be switched OFF (no vibrations) and the basket
need to be empty.

Here follows the calibration procedure:

Turn ON the main key and wait for display switching ON

Press button n.6 (SERVICE) and then press button n.7 (SETUP)

Press button n.5 (PASSWORD). The display will ask for the password

Inserting password 2857 the display will confirm with “OK”

Press button n.9 (EXIT) and then button n.8 (INCLIN.),

the display will than visualize the page here aside

With machine perfectly levelled and motors switched OFF

press button n.3 (CALIB) and verify that display

indicates “OK”

. In case of outriggers are not touching

the ground, or photocells are not aligned, or one

motor is switched on,

this page will display “NOT

READY” instead of “READY” and reset will not be

possible

INCLINATIO

N SENS. CA

LIBRATION

MACCHINA:

NOT READY

3 CALIB.

9 ESC

Содержание LightLift 15.70 3S










































































































































Результаты поиска

Содержание LightLift 15.70 3S

Отзывы:

Похожие инструкции для LightLift 15.70 3S

Бренды по названию

Популярные бренды

Hinowa LightLift 15.70 3S, Техническое руководство

Результаты поиска

Содержание LightLift 15.70 3S

Отзывы:

Похожие инструкции для LightLift 15.70 3S

Бренды по названию

Популярные бренды