Hinowa LightLift 15.70 3S Скачать руководство пользователя страница 41

Страница: 41 / 137

7.3.2

OUTRIGGERS MOVEMENT WITH THE HAND PUMP

EMERGENCY POTENTIAL SITUATIONS:



Engine and/or electric motor not working



Electrical system out of order

The only purpose of to move outriggers with the hand pump, in case of a
machine breakdown, is to lift them, after having closed and aligned the

machine, in order to get it in stowed position. Any other use is forbidden.

To carry out the movement required hydraulic oil has to be manually pumped
while using the ground valveblocks controls.

Hand pump is not designed for lift machine on the outriggers, i

t’s absolutely

forbidden to make different operations than the ones specified by the present

procedure, in particular are forbidden all of the outriggers movements while
machine is not closed and aligned or with person in the basket, in general any

operation that may compromise the machine stability.
To move an outrigger by the hand pump the here below steps have to be strictly

followed.

Make sure that the machine is closed and aligned

Turn OFF the main key

In order to move the right side outriggers, shift the deviator on the

manual pump into the position for aerial part movement/ground right
side (rightward) as indicated by the hand pump sticker and place the

hand pump lever

Содержание LightLift 15.70 3S










































































































































Результаты поиска

Содержание LightLift 15.70 3S

Отзывы:

Похожие инструкции для LightLift 15.70 3S

Бренды по названию

Популярные бренды

Hinowa LightLift 15.70 3S, Техническое руководство

Результаты поиска

Содержание LightLift 15.70 3S

Отзывы:

Похожие инструкции для LightLift 15.70 3S

Бренды по названию

Популярные бренды