Hinowa LightLift 15.70 3S Скачать руководство пользователя страница 44

Страница: 44 / 137

Press the left side proportional valve button keeping it completely pressed
while acting on the required outrigger lever as indicated at point i)

While pumping with hand pump and while proportional valve button is
completely pressed, act on the left side relevant levers, as indicated by

the sticker, to move the outriggers (n.1 and n.2)

When the emergency operation is finished it must be unscrewed the
deviator valve activator to restore the original condition

7.4

ENGINE EMERGENCY START PROCEDURE

The following procedure shows how to separate engine from the platform
system.
It could be useful in the followings cases:



To verify if the engine is out of order



To handle manually the machine’s hydraulics (by the proportional valves

and/or deviator as showed by the previous chapters) while using engine
instead of the hand pump

LEFT SIDE GROUND

PROPORTIONAL VALVE BUTTON

AND OUTRIGGERS LEVERS

Содержание LightLift 15.70 3S










































































































































Результаты поиска

Содержание LightLift 15.70 3S

Отзывы:

Похожие инструкции для LightLift 15.70 3S

Бренды по названию

Популярные бренды

Hinowa LightLift 15.70 3S, Техническое руководство

Результаты поиска

Содержание LightLift 15.70 3S

Отзывы:

Похожие инструкции для LightLift 15.70 3S

Бренды по названию

Популярные бренды