Hinowa LightLift 15.70 3S Скачать руководство пользователя страница 119 | Manualshive

Страница: 119 / 137

background image

119

When it’s

installed and activated, if Skyguard bar is kept pressed for a while,

when tracks are moving, that movement will be stopped, as soon as the bar is

release those movements will be allowed again.

Once that the bar has been pressed, the Skyguard icon is displayed, as

indicated here above and then on the bottom left corner of the display, to make
it disappear it must be pressed and released the remote control emergency

stop.

In case of need the Skyguard function could be bypassed by keeping pressed
the button n.8 of the remote control, this operation allows to move the machine

only in the case to have the bar always pressed, or stuck, but it will not allow
the movements if the bar has been pressed and released.

NOTE: With Skyguard installed, to unload the basket it has to be disconnected
the Skyguard connector.

APPENDIX 9

–

CODE MENU

The machine self-diagnostic system is able to identify eventual anomalies on
the valve coils connection, monitoring the charge detected on the valve coil is

indeed possible to determinate errors such as short circuits or connections
missing.

For some kind of anomalies affecting one aerial part valve coil, including gravity
emergency descent valves, second pump valve, etc.. all the machine aerial
part movements could be blocked for safeties reasons.

Resetting the machine by the main key (key OFF - key ON), from the software
release 2.0, if the anomaly still be present, only the specific movement affected

by that anomaly will be interdicted, the rest of the aerial part would start again
working normally.

For some kind of anomalies affecting one ground part valve coil, including
outrigger movements valves, track widening valves, etc.. all the machine

ground part movements could be blocked as well.
Resetting the machine by the main key (key OFF - key ON), from the software

release 2.0, if the anomaly still be present, only the specific movement affected
by that anomaly will be interdicted, the rest of the ground part would start

again working normally.
In case of the display shows the icon FAIL INPUT OUT, as shows here below, it

means that one anomaly at an electric connection is in progress.

ELECTRIC CONNECTION

ANOMALY IN PROGRESS

«
...
117
118
119
120
121
...
»

Содержание LightLift 15.70 3S










































































































































Отзывы:

Нет отзывов

Похожие инструкции для LightLift 15.70 3S

Бренд: KAPTARLIFT Страницы: 16

Бренд: Nedap Страницы: 5

Бренд: Xcel-Arc Страницы: 20

Бренд: mr. steam Страницы: 4

ioLogik E1500 Series

Бренд: Moxa Technologies Страницы: 6

Бренд: Aircalo Страницы: 28

Бренд: Upright Страницы: 68

Бренд: Aritech Страницы: 28

Бренд: Thermrup Страницы: 12

Бренд: AMX Страницы: 144

EMPRESS HKRAR-EMWF

Бренд: Hong Kong RFID Страницы: 34

Бренд: National Instruments Страницы: 19

Бренд: LOTOS Страницы: 14

Бренд: Soler & Palau Страницы: 20

FlexView FVS IFP Series

Бренд: Map Страницы: 16

Бренд: Parkside Страницы: 49

RTC103 N-Module

Бренд: HACH LANGE Страницы: 66

Бренд: Taramps Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды