Hinowa LightLift 15.70 3S Скачать руководство пользователя страница 95

Страница: 95 / 137

10.2

REMOTE CONTROL CONNECTION ON THE GROUND CONNECTOR

To connect remote control on the ground, using its ground cable, could be

useful in case of demonstrations or in case of particular diagnoses.
The remote control ground cable is under the slot on the left side of the electric
components compartment, installed on the machine rear side of the machine.

Connecting the remote control on the ground it’s possible to move both ground

part and aerial part, for aerial part of course remote control must not be into

its basket support

and it’s

not necessary to have the pedal pressed even in case

of it is activated.

It’s forbidden to use the remote control connected on the ground while

someone is in the basket, except for emergency reasons.

At the ground cable is connected the CONNECTOR JUMPER, necessary to close
the STOP lines on basket connector.

If the remote control is connected to the basket connector but the control

position selector switch is wrongly turned left to select the remote control
ground position, the display will show the here below icon.

The procedure to connect the remote control on the ground is detailed here
below.

Make sure that the main key on ground control box is turned OFF and

that remote control display is OFF too

Disconnect the remote control from its basket cable connector and fit the

CONNECTOR JUMPER on the same cable connector

CONNECTOR

JUMPER

REMOTE

CONTROL

GROUND

WRONG REMOTE CONTROL

POSITION SELECTED

Содержание LightLift 15.70 3S










































































































































Результаты поиска

Содержание LightLift 15.70 3S

Отзывы:

Похожие инструкции для LightLift 15.70 3S

Бренды по названию

Популярные бренды

Hinowa LightLift 15.70 3S, Техническое руководство

Результаты поиска

Содержание LightLift 15.70 3S

Отзывы:

Похожие инструкции для LightLift 15.70 3S

Бренды по названию

Популярные бренды