Gilera Runner RST 50 SP Скачать руководство пользователя страница 95

Страница: 95 / 183

- Move the crankcase separation plate in a position

back from the one indicated in the figure

- Install the special magnetic support with dial

gauge at the end of the crankshaft

- Check the axial clearance of the crankcase

If this is not within the maximum limit allowed, re-

peat the crankcase coupling procedure

Specific tooling

020335Y

Magnetic support for dial gauge

Characteristic

Axial clearance with warm crankcase

0.10 ÷ 0.12 mm

Axial clearance with cold crankcase

0.06 to 0.08 mm

Limit value with cold crankcase

0.02 ÷ 0.03 mm

Lubrication

Crankshaft oil seals

Refitting

- Install a new flywheel-side oil seal only with the

special tool's punch

The flywheel-side oil seal is recognised by its

smaller diameter

N.B.

THE USE OF THE SPECIFIC TOOL IS NOT
COMPATIBLE WITH THE FITTED WRENCH

Specific tooling

020340Y

Flywheel and transmission oil seals

fitting punch

Runner RST 50 SP

Engine

ENG - 95

Содержание Runner RST 50 SP
























































































































































































Результаты поиска

Содержание Runner RST 50 SP

Отзывы:

Gilera Runner RST 50 SP, Руководство по обслуживанию станции, Страница: 95 / 183

Результаты поиска

Содержание Runner RST 50 SP

Отзывы: