Gilera Runner RST 50 SP Скачать руководство пользователя страница 78

Страница: 78 / 183

Removing the driven pulley shaft bearing

- Remove the seeger ring inside the cover.

- Remove the oil seal from the outside.

- Remove the centring dowels and position the

cover on a plane.

- Position the special tool on the internal track of

the bearing and remove said bearing with the aid

of a press.

Specific tooling

020452Y

Tube for removing and refitting the

driven pulley shaft

- Position the special tube on the internal raceway

of the bearing and from the shaft toothed side as

indicated in the figure. Expel the driven pulley shaft

with the aid of a press.

Specific tooling

020452Y

Tube for removing and refitting the

driven pulley shaft

Inspecting the hub shaft

- Check that the three shafts exhibit no wear or

deformation on the toothed surfaces, at the bear-

ing housings and at the oil guards.

- In case of anomalies, replace the damaged com-

ponents.

- Check that the fitting surface is not dented or dis-

torted.

- If faults are found, replace the hub cover.

Inspecting the hub cover

- Check that the fitting surface is not dented or distorted.

- If faults are found, replace the hub cover.

Engine

Runner RST 50 SP

ENG - 78

Содержание Runner RST 50 SP
























































































































































































Результаты поиска

Содержание Runner RST 50 SP

Отзывы:

Gilera Runner RST 50 SP, Руководство по обслуживанию станции, Страница: 78 / 183

Результаты поиска

Содержание Runner RST 50 SP

Отзывы: