Gilera Runner RST 50 SP Скачать руководство пользователя страница 105

Страница: 105 / 183

- Using the special tool, refit the upper and lower

bearing seats on the headstock.

Specific tooling

001330Y

Tool for fitting steering seats

Steering bearing

Removal

Overhaul fifth wheel housing on fork

Check the condition of the fifth wheel and the fifth

wheel seat on the fork (steering tube). Replace if

there are faults.

- Support the fork properly.

- Using the special tool, remove the fifth wheel seat

on the steering tube as shown in the photograph

by applying small mallet blows.

Specific tooling

020004Y

Punch for removing fifth wheels from

headstock

Always use a new fifth wheel seat on refitting.

- Using the special tool, refit the fifth wheel seat

with the aid of a few mallet blows and bring it as

far as the stop shown in the photo.

Specific tooling

006029Y

Punch for fitting fifth wheel seat on

steering tube

Removing steering lock nut

Runner RST 50 SP

Suspensions

SUSP - 105

Содержание Runner RST 50 SP
























































































































































































Результаты поиска

Содержание Runner RST 50 SP

Отзывы:

Gilera Runner RST 50 SP, Руководство по обслуживанию станции, Страница: 105 / 183

Результаты поиска

Содержание Runner RST 50 SP

Отзывы: