Gilera Runner RST 50 SP Скачать руководство пользователя страница 52

Страница: 52 / 183

Specification

Desc./Quantity

Grounding for phonic wheel

Power supply to phonic wheel

Phonic wheel signal

Instrument light and parking light indicator

Instrument temperature mass

Not connected

Rpm indicator signal

Instrument temperature signal

Fuel level sensor

High-beam warning light

+ Right direction indicator

+ Left direction indicator

Low-oil warning light

Low fuel warning light

Not connected

Checks and inspections

Checks to be made in the case of ignition irregularities and/or no spark on the spark plug

1. Check the condition of the spark plug (clean it with a metal brush, remove the encrustations, blast

it with compressed air and, if necessary, replace it).

2. Without removing the stator, carry out the following checks:

After visually checking the electrical wiring, perform measurements on the loading reel, the pickup (see

chart) and the continuity using the appropriate tester.

If checks on the loading reel, pickup and continuity show abnormalities, replace the stator; otherwise

replace the central unit. Remember that disconnections due to replacement of the central unit must be

done with the engine off.

Specific tooling

020331Y

Digital multimeter

CHECK ON THE PICK UP

Specification

Desc./Quantity

Red and white cable

90±140 ohm

CHECK ON THE RELOAD REEL

Specification

Desc./Quantity

Yellow and red-blue cable

800±1100 ohm

Electrical system

Runner RST 50 SP

ELE SYS - 52

Содержание Runner RST 50 SP
























































































































































































Результаты поиска

Содержание Runner RST 50 SP

Отзывы:

Gilera Runner RST 50 SP, Руководство по обслуживанию станции, Страница: 52 / 183

Результаты поиска

Содержание Runner RST 50 SP

Отзывы: