Gilera Runner RST 50 SP Скачать руководство пользователя страница 76

Страница: 76 / 183

4) Check the integrity of the sliding blocks of the

contact plate.

- Check that the internal bushing shown in the fig-

ure is not abnormally worn and measure inside

diameter «

».

- Measure outside diameter «

» of the pulley slid-

ing bushing shown in the figure.

CAUTION

DO NOT LUBRICATE OR CLEAN THE BUSHING.

Characteristic

Driving pulley / Maximum diameter:

20.12 mm

Driving pulley/ Standard diameter:

20.021 mm

Driving pulley bushing/ Diameter maximum:

XXX mm

Driving pulley bushing/ Standard diameter:

20 -0.020/-0.041mm

Refitting the driving pulley

- Manually move the movable driven half-pulley

away by pulling it towards the clutch unit and insert

the belt observing the direction of rotation of the

first fitting.

N.B.

IT IS GOOD PRACTICE ALWAYS TO FIT THE BELT SO
THAT THE WORDS CAN BE READ IN CASE IT DOES NOT
SHOW A FITTING SIDE.

- Reassemble the unit parts (roller housing unit

with bushing, washer, stationary half pulley, belt

cooling fan with intake, washer and nut).

N.B.

REPLACE THE NUT WITH A NEW ONE AT EVERY REFIT

CAUTION

UPON FITTING THE DRIVING PULLEY UNIT IT IS OF UT-
MOST IMPORTANCE THAT THE BELT IS FREE INSIDE IN
ORDER TO AVOID WRONG TIGHTENING AND CONSE-
QUENTLY DAMAGING THE CRANKSHAFT KNURLING.

Specific tooling

020451Y

Starting ring gear lock

Engine

Runner RST 50 SP

ENG - 76

Содержание Runner RST 50 SP
























































































































































































Результаты поиска

Содержание Runner RST 50 SP

Отзывы:

Gilera Runner RST 50 SP, Руководство по обслуживанию станции, Страница: 76 / 183

Результаты поиска

Содержание Runner RST 50 SP

Отзывы: