Gilera Runner RST 50 SP Скачать руководство пользователя страница 38

Страница: 38 / 183

This section makes it possible to find the solutions to use in troubleshooting.

For each breakdown, a list of the possible causes and respective interventions is given.

Engine

Poor performance

POOR PERFORMANCE

Possible Cause

Operation

Defective fuel pump or damaged depression line

Replace the pump or control lines

Carburettor nozzles clogged or dirty

Dismantle, wash with solvent and dry with compressed air

Fuel filter on the tank outlet fitting dirty or clogged

Clean the fitting filter

Excess of encrustations in the combustion chamber

Remove the encrustations

Lack of compression wear of the piston rings or cylinder

Check the worn parts and replace them

Exhaust pipe clogged due to excessive encrustations

Replace the exhaust pipe and check the carburation and mixer

timer

Air filter blocked or dirty

Clean according to the procedure

Starter inefficient (stays on)

Check the mechanical sliding, continuity of the circuit, the pres-

ence of power and electrical wiring

Clutch slipping

Check the centrifugal brake shoe assembly and /or clutch bell

and replace if necessary

Defective mobile pulley sliding

Check the parts, change the faulty parts and lubricate the driv-

en pulley using only Montblanc-Molibdenum Grease (dis.

498345) grease

Transmission belt worn

Replace

Roller wear; Presence of oil; Dirt

Clean the speed variator, replace the rollers if worn out

Rear wheel spins at idle

REAR WHEEL

Possible Cause

Operation

Idling rpms too high

Check the idling speed and, if necessary, adjust the C.O.

Clutch fault

Check the spring/friction mass and the clutch bell

Air filter housing not sealed

Correctly refit the filter housing and replace it if it is damaged

Starting difficulties

DIFFICULTY STARTING

Possible Cause

Operation

Carburettor nozzles clogged or dirty

Dismantle, wash with solvent and dry with compressed air

Defective fuel pump or damaged depression line

Replace the pump or control lines

Starter inefficient

Check: electric wiring, circuit continuity, mechanical sliding and

power supply

Battery flat

Check the state of the battery. If it shows signs of sulphation

replace it and bring the new battery into service charging it for

eight hours at a current of 1/10 of the capacity of the battery

itself

- Engine flooded.

Start up keeping the throttle fully open alternating approximate-
ly five seconds of turning it with five seconds still. If however it
does not start, remove the spark plug, the engine over with the

throttle open being careful to keep the cap in contact with the

spark plug and the spark plug grounded but away from its hole.

Refit a dry spark plug and start the vehicle.

Altered fuel characteristics

Drain off the fuel no longer up to standard; then, refill

Defective spark plug or with incorrect electrode gap

Remove the encrustation, restore the plug gap or replace being
sure to use the types of spark plug recommended at all times.

Troubleshooting

Runner RST 50 SP

TROUBL - 38

Содержание Runner RST 50 SP
























































































































































































Результаты поиска

Содержание Runner RST 50 SP

Отзывы:

Gilera Runner RST 50 SP, Руководство по обслуживанию станции, Страница: 38 / 183

Результаты поиска

Содержание Runner RST 50 SP

Отзывы: