Gilera Runner RST 50 SP Скачать руководство пользователя страница 68

Страница: 68 / 183

- Upon refitting, apply the recommended grease to

the bushing, to the spring and along the toothed

sector.

- Use the special tool for the charging of the spring,

as shown in the figure.

- Refit the seeger ring after checking that it is in

good condition.

Specific tooling

020261Y

Starter spring fitting

Recommended products

AGIP GREASE MU3

Grease for odometer

transmission gear case

Soap-based lithium grease with NLGI 3; ISO-L-

XBCHA3, DIN K3K-20

Removing the driven pulley shaft bearing

- Slightly heat the crankshaft from the inside side

to avoid damaging the coated surface and use the

driven pulley shaft or a pin of the same diameter

to remove the bearing.

N.B.

IN CASE OF DIFFICULTY A STANDARD 8MM-INSIDE DI-
AMETER EXTRACTOR CAN BE USED.

Refitting the driven pulley shaft bearing

-Refit the bearing with the aid of a bushing with the same diameter as the external plate of the bearing

after slightly heating the crankcase from the inside.

N.B.

WHEN REFITTING, ALWAYS REPLACE THE BEARING WITH A NEW ONE.

CAUTION

WHEN REMOVING/REFITTING THE BEARING, TAKE CARE NOT TO DAMAGE THE PAINTED
SURFACE.

Engine

Runner RST 50 SP

ENG - 68

Содержание Runner RST 50 SP
























































































































































































Результаты поиска

Содержание Runner RST 50 SP

Отзывы:

Gilera Runner RST 50 SP, Руководство по обслуживанию станции, Страница: 68 / 183

Результаты поиска

Содержание Runner RST 50 SP

Отзывы: