Gilera Runner RST 50 SP Скачать руководство пользователя страница 103

Страница: 103 / 183

Loctite 243 medium-strength threadlock

Locking torques (N*m)

Stud-stanchion fixing screw

20 to 25 N•m

Nut

tightening torque

20 to 25 N•m

Replacing sealing ring

- Remove the wheel axle.

- Remove the screw (4).

- Remove the stanchion (3).

- Remove the dust guard (1).

- Insert the new sealing ring after lubricating the

inside parts of the ring and paying attention not to

damage it.

- Insert the stanchion appIying the recommended

product to the clean surface.

- Lock the screw (4).

Recommended products

Loctite 243

Medium strength threadlock

Loctite 243 medium-strength threadlock

Removing stanchion bracket

- Remove the dust guard (1) using a screwdriver

to prise it out.

- Remove the seeger (2) and remove the power

pipe.

N.B.

GREASE THE SPRINGS AND THE BUSHINGS BEFORE
REFITTING, WITH A SMALL QUANTITY OF GREASE
(AROUND 3 GR.)

Recommended products

AGIP GREASE MU3

Grease for odometer

transmission gear case

Soap-based lithium grease with NLGI 3; ISO-L-

XBCHA3, DIN K3K-20

Refitting

Lubricate the seats and the balls with the grease

recommended.

Runner RST 50 SP

Suspensions

SUSP - 103

Содержание Runner RST 50 SP
























































































































































































Результаты поиска

Содержание Runner RST 50 SP

Отзывы:

Gilera Runner RST 50 SP, Руководство по обслуживанию станции, Страница: 103 / 183

Результаты поиска

Содержание Runner RST 50 SP

Отзывы: