Gilera Runner RST 50 SP Скачать руководство пользователя страница 100

Страница: 100 / 183

- Remove the internal spacer

- Use appropriate handle, adaptor and guide and

hit with a mallet to extract the bearing and the

spacer bushing on the brake disk side; insert han-

dle on the side the rpm indicator detects move-

ment, as shown in the photo

Specific tooling

020376Y

Adaptor handle

020456Y

Ø 24 mm adaptor

020412Y

15 mm guide

- Check that the bearings do not show flaws or

jamming. If there is, replace it.

- Check that the internal spacer does not show ab-

normal wear. If there is, replace it.

- With a hot air gun heat the seat of the bearing on

the brake calliper side

- With an appropriate tool remove the bearing on

the brake disk side

- Insert the spacer bushing on the brake disk side

Specific tooling

020376Y

Adaptor handle

020357Y

32 x 35 mm adaptor

020412Y

15 mm guide

- With a hot air gun heat the seat of the bearing on

the side the rpm indicator detects movement

- Insert the internal spacer with the centring ring

facing to the brake disk side, as shown in the photo

- Use an appropriate tool to insert the bearing on

the rpm indicator movement detector side

Specific tooling

020376Y

Adaptor handle

020357Y

32 x 35 mm adaptor

020412Y

15 mm guide

See also

Suspensions

Runner RST 50 SP

SUSP - 100

Содержание Runner RST 50 SP
























































































































































































Результаты поиска

Содержание Runner RST 50 SP

Отзывы:

Gilera Runner RST 50 SP, Руководство по обслуживанию станции, Страница: 100 / 183

Результаты поиска

Содержание Runner RST 50 SP

Отзывы: